Multicomponent AlSiNiCoFeCr and AlSiNiCoFeCrTi High-Entropy Coatings on Steel

Authors

DOI:

https://doi.org/10.20535/1810-0546.2017.2.96410

Keywords:

High-entropy alloy, Electron beam welding, Coating, Structure, Phase composition, Microhardness

Abstract

Background. In many situations, only the contact surface properties are important in determining performance of the component in practical applications. Therefore, the use of a coating from materials with high physical and mechanical characteristics, such as high-entropy alloys (HEA), has several attractive advantages. HEAs have been found to have novel microstructures and unique properties. Considering HEA’s tendency to form simple structures, fabricating HEA coating by electron beam welding process is of great significance and potential for extensive use. Until now this novel method for preparing HEA coatings has just been reported by any organizations.

Objective. The purpose of this work is to study the features of microstructure, phase and chemical composition, and microhardness of HEA coatings, produced by electron-beam welding on steel substrate of 6 and 7-component powder equiatomic mixtures of the system Al–Si–Ni–Со–Fe–Cr–Ti.

Methods. The coatings were obtained by electron-beam welding. The microstructure, chemical composition, and constituent phases of the synthesized coatings were characterized by SEM, EDX, and XRD analysis, respectively. Microhardness was also evaluated.

Results. Experimental results demonstrate that the AlSiNiСоFeCr and AlSiNiСоFeCrTi HEA coatings are composed of only three substitutional solid solutions with body-centered cubic (BCC) structure and different lattice parameter due to different component concentration. The coatings exhibit dendritic microstructure with different size and morphology. The Vickers’s hardness of AlSiNiСоFeCr and AlSiNiСоFeCrTi HEA coatings has been found to be HV = 9.2 ± 0.2  and HV = 11.25 ± 0.3 GPa, respectively, and is much higher than that of the similar alloys prepared by laser cladding technique.

Conclusions. Evidence from multicomponent powder mixtures of the Al–Si–Ni–Со–Fe–Cr–Ti system, it is possible to form HEA coatings consisting of solid substitution solutions with a BCC structure and all initial components by electron-beam welding method. Through the strong crystal lattice distortion of solid solutions at the mutual dissolving of dissimilar atoms of AlSiNiCoFeCr and AlSiNiCoFeCrTi, HEA coatings have a high microhardness that is much higher than the hardness of the initial components.

Author Biographies

Aleksandra Yurkova, Igor Sikorsky Kyiv Polytechnic Institute

Professor at the Department of high-temperature materials and powder metallurgy

Vadim Cherniavskyi, Igor Sikorsky Kyiv Polytechnic Institute

Junior researcher at the Department of high-temperature materials and powder metallurgy

Alexandr Matveev, Igor Sikorsky Kyiv Polytechnic Institute

Student at the Department of high-temperature materials and powder metallurgy

Sergiy Gangzuk, Igor Sikorsky Kyiv Polytechnic Institute

Student at the Department of high-temperature materials and powder metallurgy

References

J.W. Yeh et al., “Nanostructured high-entropy alloys with multiple principal elements: Novel alloy design concepts and outcomes”, J. Adv. Eng. Mater., vol. 6, no. 5, pp. 299–303, 2004. doi: 10.1002/adem.200300567

B. Cantor et al., “Microstructural development in equiatomic multicomponent alloys”, J. Mater. Sci. Eng. A, vol. 375-377, pp. 213–218, 2004. doi: 10.1016/j.msea.2003.10.257

X. Yang et al., “Microstructure and compressive properties of NbTiVTaAlx high entropy alloys”, Procedia Engineering, vol. 36, pp. 292–298, 2012. doi: 10.1016/j.proeng.2012.03.043

J.H. Pi et al., “Microstructure and property of AlTiCrFeNiCu high-entropy alloy”, Alloys and Compounds, vol. 509, no. 18, pp. 5641–5645, 2011. doi: 10.1016/j.proeng.2012.03.043

J.-W.Yeh et al., “High-entropy alloys – A new era of explotation”, Mater. Sci. Forum, vol. 560, pp. 1–9, 2007. doi: 10.4028/www.scientific.net/MSF.560.1

S. Guo et al., “Phase stability in heas: Formation of solid-solution phase or amorphous phase”, Progress in Natural Science: Materials International, vol. 21, no. 6, pp. 433–446, 2011. doi: 10.1016/S1002-0071(12)60080-X

O.I. Yurkova et al., “Formation of structure and phase composition in ecviatomic alloys of Cu–Ni–Al–Fе–Cr system synthesized by mechanical alloying”, Naukovi Visti NTUU KPI, no. 5, pp. 93–99, 2014 (in Ukrainian).

A.I. Yurkova et al., “Structure and mechanical properties of high-entropy AlCuNiFeTi and AlCuNiFeCr alloys produced by mechanical activation followed by pressure sintering”, Powder Metall. Met. Ceram., vol. 55, no. 3, pp 152–163, 2016. doi: 10.1007/s11106-016-9790-3

J.-W Yeh et al., “Anomalous decrease in X-ray diffraction intensities of Cu-Ni-Al-Co-Cr-Fe-Si alloy systems with multi-principal elements”, Mater. Chem. Phys. vol. 103, no. 1, pp. 41–46, 2007. doi: 10.1016/j.matchemphys.2007.01.003

X. Yang et al., “Microstructure and compressive properties of NbTiVTaAlx high entropy alloys”, Procedia Engineering, vol. 36, pp. 292–298, 2012. doi: 10.1016/j.proeng.2012.03.043

L. Kaufman and H. Bernstein, Computer Calculation of Phase Diagrams. New York: Academic Press, 1970.

T.T. Shun et al., “The effects of secondary elemental Mo or Ti addition in Al0.3CoCrFeNi high-entropy alloy on age hardening at 700 °C”, J. Alloy. Compd., vol. 495, no. 1, pp. 55–58, 2010. doi: 10.1016/j.jallcom.2010.02.032

M.C. Gao et al., “Searching for next single-phase high-entropy alloy compositions”, Entropy, vol. 15, no. 10, pp. 4504–4519, 2013. doi: 10.3390/e15104504

N.N. Greenwood and A. Earnshaw, Chemistry of the Elements. Oxford, UK: Butterworth-Heinemann, 1997.

H. Zhang et al., “Synthesis and characterization of FeCoNiCrCu high-entropy alloy coating be laser cladding”, Materials and Design, vol. 32, no. 4, pp. 1910–1915, 2011. doi: 10.1016/j.matdes.2010.12.001

H. Zhang et al., “Microstructure and properties of 6FeNiCoSiCrAlTi high-entropy alloy coating prepared by laser cladding”, Appl. Surf. Sci., vol. 257, no. 6, pp. 2259–2263, 2011. doi: 10.1016/j.apsusc.2010.09.084

Published

2017-04-27

Issue

Section

Art