The cutting forces at thin cubonit grinding of the wear-resistant composite nickel-based parts for printing machines

Authors

DOI:

https://doi.org/10.20535/1810-0546.2016.1.63586

Keywords:

New composite materials, Cutting forces, Grinding cubonit discs, Grain, Bond type, Cubonit grinding, Cutting modes

Abstract

Background. The investigation of the influence on the cutting forces rectangular components of technological factors at thin cubanite grinding of parts made of wear-resistant composite materials synthesized based on the use of recycled and regenerated waste products of nickel alloys XH55BMTKЮ, XH50BTФKЮ, ЭП975 with the addition of solid lub­­ricant CaF2 is presented.

Objective. The purpose of the paper is the experimental research of cutting forces rectangular components of tech­nological processes of thin cubanite grinding of friction parts made of new nickel-based composite materials. The influence on the force field of grinding tool grain, such as bond type grinding discs and basic grinding modes, is determined.

Methods. Surface treatment of printing machine friction parts made of wear-resistant nickel-based composites with thin grinding on the plain-grinding machines with cubonit grinding instruments with 14–20 µm grain on the bakelite-rubber bond Бр1 and use of the thin cutting modes.

Results. It was show, that the granularity, grinding disc bond material and thin cubonit grinding modes essentially influence the cutting forces rectangular components Px, Py, Pz at grinding of the new nickel-based composites. The cubonit discs with 14–20 µm grain on the bakelite-rubber bond Бр1 and use of the thin cutting modes provided the best results.

Conclusions. It is proved that the grain and the grinding cubanite discs bond type and grinding modes significantly influence the formation of the force field at grinding of new nickel-based composite materials. The recommendations were developed for the production.

Author Biographies

Анатолій Павлович Гавриш, National Technical University of Ukraine "Kyiv Polytechnic Institute"

Anatoliy P. Gavrish,

doctor of technical sciences, professor, professor at the Department of Printing and Publishing Technologies of Institute of Publishing and Printing

Тетяна Анатоліївна Роїк, National Technical University of Ukraine "Kyiv Polytechnic Institute"

Tatyana A. Roik,

doctor of technical sciences, professor, professor at the Department of reprography of Institute of Publishing and Printing

Петро Олексійович Киричок, National Technical University of Ukraine "Kyiv Polytechnic Institute"

Petro O. Kyrychok,

doctor of technical sciences, professor, vice-rector for educational work

Розалія Анатоліївна Хохлова, National Technical University of Ukraine "Kyiv Polytechnic Institute"

Rozaliіa A. Khokhlova,

associate professor, assistant professor at the Department of reprography of Institute of Publishing and Printing

References

A. Kostornov, Tribotechnical Material Science. Lugansk, Ukraine: Nouly, 2012, 701 p. (in Russian).

I. Fedorchenko et al., Powder Metallurgy. Materials, Technology, Properties, Ranges of Application. Kyiv, USSR: Naukova Dumka, 1985, 624 p. (in Russian).

G. Lebenson, Production of Powder Parts. Moscow, USSR: Metallurgia, 1990, 240 p. (in Russian).

I. Fedorchenko et al., Sintered Composite Antifriction Materials. Kyiv, USSR: Naukova Dumka, 1980, 404 p. (in Russian).

T. Roik et al., Composite Bearing Materials for Service Condition Increase. Kyiv, Ukraine: Polіtekhnіca, 2007, 404 p. (in Ukrainian).

T. Roik et al., New Composite Materials for Printing Machines Friction Parts. Kyiv, Ukraine: Polіtekhnіca, 2014, 427 p. (in Ukrainian).

P. Kyrychok et al., Printing Production Technology. Kyiv, Ukraine: Polіtekhnіca, 2014, 504 p. (in Ukrainian).

B. Kostetsky et al., Reliability and Longevity of Machines. Kyiv, USSR: Technіcs, 1975, 408 p. (in Russian).

B. Kostetsky, Fundamental Questions at Theory of Friction and Wearing the Parts of Machine. Moscow, USSR: Mashgiz, 1955, 152 p. (in Russian).

B. Kostetsky et al., Surface Strength of Materials at Friction. Kyiv, USSR: Naukova Dumka, 1982, 126 p. (in Russian).

I. Kragelsky et al., Friction and Wearing. Moscow, USSR: Mashinostroenie, 1968, 478 p. (in Russian).

I. Kragelsky et al., Foundations Analysis on the Friction and Wearing. Moscow, USSR: Mashinostroenie, 1977, 526 p. (in Russian).

E. Rizhov, Technological Methods for Machine Parts Durability Improvement. Kyiv, USSR: Naukova Dumka, 1984, 340 p. (in Russian).

E. Rizhov, Contact Rigidity of Machine Parts. Kyiv, USSR: Naukova Dumka, 1987, 320 p. (in Russian).

A. Gavrish and P. Melnychuk, Diamond-Abrasive Treatment of Magnetic Materials. Zhytomyr, Ukraine: ZDTU, 2003, 652 p. (in Ukrainian).

A. Gavrish, Grinding and Finishing of Magnetic Materials. Leningrad, USSR: Mashinostroenie, 1985, 118 p. (in Russian).

P. Kyrychok et al., Finishing Processing of Printing Machine Wear-Resistant Parts. Kyiv, Ukraine: Polіtekhnіca, 2014, 404 p. (in Ukrainian).

E. Maslov, Material Grinding Theory. Moscow, USSR: Mashinostroenie, 1974, 320 p. (in Russian).

M. Mazur et al., Basic Theory of Cutting Materials. Lviv, Ukraine: Novyj Svit, 2010, 423 p. (in Ukrainian).

P. Yascheritsyn, Advanced Technology of Parts Finishing Processing. Minsk, USSR: Belarus, 1989, 312 p. (in Russian).

Super Hard Material Tools, N. Novikov and S. Klimenko, Eds. Moscow, Russia: Mashinostroenie, 2014, 607 p. (in Russian).

V. Lavrinenko and N. Novіkov, Super Hard Abrasives in Machines. Kyiv, Ukraine: ІSM of NAІU, 2013, 456 p. (in Ukrainian).

Super Hard Materials. Preparation and Usage, N. Novikov, Ed, vol. 6. Diamond Abrasive Instrument in the Processing Technologies, A. Shepelev, Ed. Kyiv, Ukraine: ІSM of NAІU, 2007, 340 р. (in Russian).

Elbor in Mechanical Engineering, V. Lysanov, Ed. Moscow, USSR: Mashinostroenie, 1978, 280 p. (in Russian).

Published

2016-03-10

Issue

Section

Art